Firearms

 

image

exceeding the needs

for all your

firearms maintenance

requirements!

 

STANDARD FIREARMS

 

Firearms Maintenance Kit

Firearms Maintenance Pack

 

BLACK POWDER

 

BP Firearms Maintenance Kit

BP Firearms Maintenance Pack


 

OTHER USES

 

About Bore Conditioning & Breakin

Shotgun Choke Tubes

Case Resizing Lube


 

 


         

 


 

image

 

Firearms Maintenance Kit

 

 

PRODUCT:

05100

 

A3 Pump Spray Cleans-Lubes-Protects

4 oz

 

Bore Conditioner

2 oz

 

Grease - Extreme Pressure

1 oz

 

Bore Conditioning – No special preparation is required.  Simply start using RyDol Bore Conditioner.   Your bore will be conditioned with continued use. You will notice an ease of cleaning and how the cleaning rod will slide through the bore with much less resistance; a cleaner firearm overall.

Here is how it works. RyDol contains BORON NITRIDE and PTFE micron sized particles in colloidal suspension which displace any built up carbon, lead or copper gilding.  Through repeated use, RyDol penetrates through and under debris in the bore and into the bearing surfaces of the lands and grooves.  This process produces a super slick, consistent surface. The debris is blown out with each shot.  The payoff is a tighter group and a slight increase in velocity!  Clean your bore often.   Professionals do. The more you use RyDol the better your firearm performs.  RyDol is non-corrosive and non-abrasive. 

New GunsRyDol Bore Conditioner  should be used to break-in a new firearm. Here is a recommended procedure for a Target Rifle or similar firearm.

1.       Spray RyDol A3  into the bore and scrub the new bore with a bare bore brush. This removes any light oil from the factory armory.

2.       Saturate a patch with RyDol Bore Conditioner and run the patch through several times (5-10).  Leave a light and wet coat.
 

CAUTION: EXCESS MAY CAUSE DANGEROUS PRESSURE WHEN FIRING!

Fire a single round and re-apply RyDol Bore Conditioner. Repeat for 5-10 shots. Then repeat the procedure for a pair of 5 shot groups; a total of 10 shots; two treatments. Ignore the size of the group; shots will be sporadic.

Note:  Do not use a bore brush with a patch. Brushes are for brushing; Patches are for patching; two separate actions.

3.       Run a dry patch(s) through the bore until no residue is present on the patch.

4.       Use a light amount of RyDol EP Grease on the Thread and cams. Work the action several times then wipe off excess.

5.   Your firearm is now ready for use.

Continue using RyDol A3 for routine cleaning and maintenance.   RyDol does not replace metal that has already worn away; however, it will slow the wear process and extend the life of the barrel and other working parts.  If practical, always run a dry patch through the bore immediately before using your firearm, especially if it has sat for over a day or more.  This is for safety, good maintenance, care and accuracy. 

BLACK POWDER and SHOTGUNS require a similar but less rigorous break-in procedure.

SHOTGUN SCREW-IN CHOKES:  Use RyDol as a non-seize lubricant for screw-in chokes.

Firearms External Preservation: Use RyDol to wipe down firearms for external preservation.

RyDol prevents rust and corrosion, repels water, salt, sand and dust.

 

Rydol.com     info@rydol.com     877-727-7912

P.O.  Box 606
Shelbyville, KY 40066
Product:  05100


 

image

 

Firearms Maintenance Pack

 

 

 

PRODUCT:

05200

 

Aerosol Spray Cleans-Lubes-Protects

6 oz

 

Bore Conditioner

2 oz

 

Grease - Extreme Pressure

1 oz

 

* Instructions are the same as the KIT *

 


 

image

 

BLACK POWDER

Firearms Maintenance Kit

 

 

  

Solvent Cleaner-Lube-Preservative
- 4 oz Spray

Bore Conditioner - 2 oz

Grease - 1 oz

 

 PRODUCT #: 05300

 

 

Lube the Patch – Wet shooting patches with RyDol Spray Lube and shoot.

Clean up – When shooting is complete, spray RyDol into the bore and patch until it comes out clean.

Spray the outside, especially around the nipple/hammer area and use a toothbrush to loosen carbon and then wipe down and remove the carbon on the barrel and stock with a soft cloth.   Remove the nipple and clean the threads on the nipple and in the receiver with a wet patch.   Occasionally, remove and clean the set screw and threads of the ignition chamber access hole.

Bore Conditioning RyDol is a concentrate in light oil and contains no solvent.  Simply start using RyDol Bore Conditioner.   Your bore will be conditioned with continued use. You will notice an ease of cleaning and how the cleaning brush will slide through the bore with much less resistance; a cleaner firearm overall.  Use RyDol Bore Conditioner on occasion whereas RyDol Spray Lube – Cleaner – Preservative will also condition your bore through continued routine use. 

Here is how it works. RyDol contains HEXAGONAL BORON NITRIDE and PTFE micron sized particles in colloidal suspension which displace any built up carbon, lead or copper gilding.  Through repeated use, RyDol penetrates through and under debris in the bore and into the bearing surfaces of the lands and grooves.  This process produces a super slick, consistent surface. The debris is blown out with each shot.  The payoff is a tighter group and a slight increase in velocity!  Clean your bore often.   Professionals do. The more you use RyDol the better your firearm performs.  RyDol is non-corrosive and non-abrasive. 

New Guns RyDol Bore Conditioner should be used to break-in a new firearm. Here is a recommended procedure for a Black Powder firearm or similar firearm.

1.     Spray RyDol into the bore and scrub the new bore with a bare bore brush. This removes any light oil from the factory armory.

2.    Saturate a patch with RyDol Bore Conditioner and run the patch through several times (5-10).  Leave a light and wet coat.
 

    CAUTION: EXCESS MAY CAUSE DANGEROUS PRESSURE WHEN FIRING!

 

Fire a single round and re-apply RyDol Bore Conditioner. Repeat for 5-10 shots. Then repeat the procedure for a pair of 5 shot groups; a total of 10 shots; two treatments. Ignore the size of the group; shots will be sporadic.

Note:  Do not use a bore brush with a patch. Brushes are for brushing; Patches are for patching; two separate actions.

3.     Run a dry patch(s) through the bore until no residue is present on the patch.

4.     Use a light amount of RyDol EP Grease on the trigger sear. Work the trigger several times then wipe off excess.

5.   Your firearm is now ready for use.

Continue using RyDol spray for routine cleaning and maintenance.   RyDol does not replace metal that has already worn away; however, it will slow the wear process and extend the life of the barrel and other working parts.  If practical, always run a dry patch through the bore immediately before using your firearm, especially if it has sat for over a day or more.  This if for safety, good maintenance, care and accuracy. 

SHOTGUNS require a similar but less rigorous break-in procedure.

SHOTGUN SCREW-IN CHOKES:  Use RyDol EP Grease as a non-seize lubricant for screw-in chokes.

Firearms External Preservation – Use RyDol spray  to wipe down firearms for external preservation. RyDol prevents rust and corrosion, repels water, salt, sand and dust.

RyDol Spray can also be used as a case lube for resizing.  Lay out brass and spray lightly; mix and spray again.  Begin resizing.

 

Rydol.com     info@rydol.com     877-727-7912

P.O.  Box 606
Shelbyville, KY 40066
Product:  05300

 

 

image

 

BLACK POWDER

Firearms Maintenance Pack

 

 

  

Aerosol Spray Cleaner-Lube-Preservative
- 6 oz Aerosol Spray

Bore Conditioner - 2 oz

Grease - 1 oz

 

 PRODUCT #: 05400

 

Lube the Patch – Wet shooting patches with RyDol Spray Lube and shoot.

Clean up – When shooting is complete, spray RyDol into the bore and patch until it comes out clean.

Spray the outside, especially around the nipple/hammer area and use a toothbrush to loosen carbon and then wipe down and remove the carbon on the barrel and stock with a soft cloth.   Remove the nipple and clean the threads on the nipple and in the receiver with a wet patch.   Occasionally, remove and clean the set screw and threads of the ignition chamber access hole.

Bore ConditioningRyDol is a concentrate in light oil and contains no solvent.  Simply start using RyDol Bore Conditioner.   Your bore will be conditioned with continued use. You will notice an ease of cleaning and how the cleaning brush will slide through the bore with much less resistance; a cleaner firearm overall.  Use RyDol Bore Conditioner on occasion whereas RyDol Spray Lube – Cleaner – Preservative will also condition your bore through continued routine use. 

Here is how it works. RyDol contains HEXAGONAL BORON NITRIDE and PTFE micron sized particles in colloidal suspension which displace any built up carbon, lead or copper gilding.  Through repeated use, RyDol penetrates through and under debris in the bore and into the bearing surfaces of the lands and grooves.  This process produces a super slick, consistent surface. The debris is blown out with each shot.  The payoff is a tighter group and a slight increase in velocity!  Clean your bore often.   Professionals do. The more you use RyDol the better your firearm performs.  RyDol is non-corrosive and non-abrasive. 

New GunsRyDol Bore Conditioner should be used to break-in a new firearm. Here is a recommended procedure for a Black Powder firearm or similar firearm.

1.     Spray RyDol into the bore and scrub the new bore with a bare bore brush. This removes any light oil from the factory armory.

2.     Saturate a patch with RyDol Bore Conditioner and run the patch through several times (5-10).  Leave a light and wet coat.
 

       CAUTION: EXCESS MAY CAUSE DANGEROUS PRESSURE WHEN FIRING!

 

Fire a single round and re-apply RyDol Bore Conditioner. Repeat for 5-10 shots. Then repeat the procedure for a pair of 5 shot groups; a total of 10 shots; two treatments. Ignore the size of the group; shots will be sporadic.

Note:  Do not use a bore brush with a patch. Brushes are for brushing; Patches are for patching; two separate actions.

3.     Run a dry patch(s) through the bore until no residue is present on the patch.

4.     Use a light amount of RyDol EP Grease on the trigger sear. Work the trigger several times then wipe off excess.

5.   Your firearm is now ready for use.

Continue using RyDol spray for routine cleaning and maintenance.   RyDol does not replace metal that has already worn away; however, it will slow the wear process and extend the life of the barrel and other working parts.  If practical, always run a dry patch through the bore immediately before using your firearm, especially if it has sat for over a day or more.  This if for safety, good maintenance, care and accuracy. 

SHOTGUNS require a similar but less rigorous break-in procedure.

SHOTGUN SCREW-IN CHOKES:  Use RyDol EP Grease as a non-seize lubricant for screw-in chokes.

Firearms External Preservation – Use RyDol spray  to wipe down firearms for external preservation. RyDol prevents rust and corrosion, repels water, salt, sand and dust.

RyDol Spray can also be used as a case lube for resizing.  Lay out brass and spray lightly; mix and spray again.  Begin resizing.

Rydol.com     info@rydol.com     877-727-7912

P.O.  Box 606
Shelbyville, KY 40066
Product:  05400


 

image

Cleaning Green Ball.gif (257 bytes) Lubricating Green Ball.gif (257 bytes) Bore Conditioning

 

High Pressure Friction Tests
(Product Comparison Charts)
Grease Oil Spray Cleaner/Lubes
chart-grease.gif (5999 bytes) chart-oil.gif (6636 bytes) chart-spray.gif (6084 bytes)
Click on a chart to view normal size

 

About RyDol Bore Conditioning and Break-In

RyDol Extreme Pressure Grease is a proprietary formula which combines years of tribological breakthroughs and proven materials in extreme pressure lubrication systems.

 


 

image


BORE CONDITIONING

AND

BREAK-IN

 

 

Bore-Conditioning – No special preparation is required.  Simply start using RyDol Bore Conditioner.   Your bore will be conditioned with continued use. You will notice an ease of cleaning and how the cleaning rod will slide through the bore with much less resistance; a cleaner firearm overall.

Here is how it works. RyDol contains BORON NITRIDE and PTFE micron sized particles in colloidal suspension which displace any built up carbon, lead or copper gilding. Through repeated use, RyDol penetrates through and under debris in the bore and into the bearing surfaces of the lands and grooves. This process produces a super slick, consistent surface. The debris is blown out with each shot. The payoff is a tighter group and a slight increase in velocity!  Clean your bore often.   Professionals do. The more you use RyDol the better your firearm performs.  RyDol is non-corrosive and non-abrasive. 

New Guns RyDol Bore Conditioner  should be used to break-in a new firearm. Here is a recommended procedure for a Target Rifle or similar firearm.

1.    Spray RyDol A3  into the bore and scrub the new bore with a bare bore brush. This removes any light oil from the factory armory.

2.    Saturate a patch with RyDol Bore Conditioner  and run the patch through several times (5-10). Leave a light, wet coat.

CAUTION: EXCESS MAY CAUSE DANGEROUS PRESSURE WHEN FIRING!

Fire a single round and re-apply RyDol Bore Conditioner. Repeat for 5-10 shots. Then repeat the procedure for a pair of 5 shot groups; a total of 10 shots; two treatments. Ignore the size of the group; shots will be sporadic.

Note: Do not use a bore brush with a patch. Brushes are for brushing; Patches are for patching; two separate actions.

3.    Run a dry patch(s) through the bore until no residue is present on the patch.

4.    Use a light amount of RyDol EP Grease on the Thread and cams. Work the action several times then wipe off excess.

5.    Your rifle is now ready for use.

 

Continue using RyDol  A3  for routine cleaning and maintenance. RyDol does not replace metal that has already worn away; however, it will slow the wear process and extend the life of the barrel and other working parts.  If practical, always run a dry patch through the bore immediately before using your firearm, especially if it has sat for over a day or more. This if for safety, good maintenance, care and accuracy.  BLACK POWDER and SHOTGUNS require a similar but less rigorous break-in procedure.

SHOTGUN SCREW-IN CHOKES: Use RyDol as a non-seize lubricant for screw-in chokes.

 

Firearms External Preservation – Use RyDol to wipe down firearms for external preservation. RyDol prevents rust and corrosion, repels water, salt, sand and dust.

 

 

RyDol Products, PO Box 606,

Shelbyville, KY 40066-0606

TEL/FAX 1-877-727-7912 Green Ball.gif (257 bytes) rydol.com Green Ball.gif (257 bytes) info@rydol.com

 


 

image

 

 

SHOTGUN CHOKE TUBES

 

 

 

When installing Shotgun Choke Tubes you need to apply an extreme pressure, Non-seize Grease to the threads.   Whether you are after Upland Game Birds, Sporting Clays, Turkey or Deer, a choke tube needs removed and lubricated after a day’s shooting.  Especially in the case of a “rifled” tube for deer slugs. Each shot torques the tube even tighter.  Without proper lubrication it may become impossible to remove by only a gunsmith and he will probably have to damage your tube. 

RyDol Extreme Pressure Non-Seize GREASE will solve these problems.

Order a 1 oz jar, #05001 today!


 

CASE RESIZING LUBE

 

  

The RyDol Aerosol or A3 Pump Spray can also be used as a case lubricant for resizing.

 

Lay brass out and apply a light spray.   Reposition and apply another

Light coat of spray. 

 

Your brass is now ready to resize.

 

RyDol Aerosol Spray Lube                          95600                    6 oz    $5.00

 

RyDol A3 Pump Spray Lube                       95004                    4 oz    $3.95

 


 

RyDol A3 3-Way Action Spray

RyDol A3 3-Way Action Spray Lube-Cleaner can be used for break-in and general maintenance.

RyDol Extreme Pressure Grease

RyDol Extreme Pressure Grease contains both molybdenum disulfide, BORON NITRIDE and PTFE for high performance. 

General Maintenance Tip: "Grease a Rifle and Oil a Pistol"

RyDol products are compatible with Moly coated bullets.

 


 

About RyDol GREASE  

Rydol.com     info@rydol.com     877-727-7912

P.O.  Box 606
Shelbyville, KY 40066
Product:  05300